By using two helmets that are both equipped with BX4 systems (or subsequent versions), bike-to-bike communication is possible up to a maximum distance of about 500 metres, in open field, with no obstacles.

In case the bike-to-bike intercom is open and connection with the other pilot is lost due to range limits being exceeded, the system will automatically reconnect as soon the two motorcycles are within a distance such as to allow communication.

Sound quality depends on the audio equipment used and on the volume level. The volume of the audio device or of the BX4 should be adjusted so that it is not too high, as this might distort the sound.

Warning: Listening to other equipment should not interfere with driving the vehicle, which is top priority. Carry out all operations on the electronic equipment and on the N-Com system with the vehicle stopped, in compliance with Traffic Regulations.

Warning: Listening to high volume levels can distract you from driving the vehicle and may result in dangerous situations or reduce the ability to hear external noise.

Warning: Listening to high volume levels may result in hearing damage.

Yes, by downloading the “N-Com Wizard” programme from the "download" section.

The BX4 system is certified by the Bluetooth SIG Association, and it is therefore compatible with mobile phones equipped with a certified Bluetooth system. However, not all the functions on mobile phones might be available. For further information, refer to the Internet site.

Yes. The BX4 system allows each helmet, the rider’s or the passenger's, to maintain connection to the phone and to the other helmet.

The connection between the rider's helmet and the passenger's is put on hold and the rider is able to take the call. The passenger will not hear the caller's voice, and will not be heard by the caller.
Rider and passenger will be automatically reconnected at the end of the phone call.
If you wish, you can activate the “Conference Call Function”.

When a call comes in on a mobile phone connected via Bluetooth to a BX4, the Rider-Passenger intercom is temporarily cut off. If you wish, however, you can share the incoming call with the other helmet by simply opening the intercom manually during the phone call (by briefly pressing "on").

Caution: this function is available only if the Pillion Passenger helmet is also equipped with a N-Com system provided with the same function.

You can listen to music via Bluetooth connection with a mobile phone in Stereo mode if the mobile phone is equipped with an A2DP profile. To check if this is the case, please refer to your mobile phone manufacturer’s webpage or go to www.a2dp.info.
Some mobile phones send music to the helmet by means of the Hands-Free (HF) profile, which is normally used for phone calls. The resulting audio quality will be inferior and sound will be emitted in Mono mode.

Yes. Each time "+" or "-" are pressed (a confirmation beep is heard in the earphones), the volume goes up or down a level, until a high (maximum) or low-pitched (minimum) beep is sounded.

The BX4 system can only connect to one device at a time. However, it can store more than one device previously paired up. When turned on, the system automatically searches for the last used device that can be found in its range.

This function is only possible in case the paired-up devices (MP3 players, mobile phones) are equipped with A2DP profile.

A2DP (Advanced Audio Distribution Profile) is a Bluetooth profile for high sound quality playback from an audio source equipped with this profile. N-Com BX4 is equipped with A2DP and can therefore be connected to mobile phones or music players that reproduce audio using this profile.

Please refer to your mobile phone manufacturer’s webpage or go to www.a2dp.info.

AVRCP (Audio Video Remote Control Profile) is a specific Bluetooth profile designed to control, via Bluetooth, Mp3 players (or mobile phones) equipped with A2DP. With the N-Com BX4, you can use the Play, Pause, Forward (Next track) controls directly from the helmet, with no need for manual operations from the connected device.

Yes. Just pair up the N-Com BX4.

Yes. However, one signal will overlap the other.

Press "+" for 2 seconds to activate the "Pause" control during Bluetooth audio playback. The audio via cable will still be transferred.

Both rider and passenger will be able to hear the music. If the passenger is disconnected, he/she will be cut off and will not be able to listen to the music. While music is playing, the intercom is on and you can talk with music in the background.

No. Another helmet cannot be connected via Bluetooth if the A2DP profile is used.

No. It is not possible to connect a passenger and an Mp3 player via Bluetooth at the same time.

Yes. The passenger will be able to listen to the music from the rider's Mp3 player and you will be able to talk to each other in intercom mode. The passenger will listen to high quality sound music in Stereo mode.

If the two helmets are connected via Bluetooth, both can use the "IN" connector to connect to an audio device. The audio from the connected devices will be heard by both rider and passenger.

Bluetooth intercom transmission of music sources (FM radio or MP3 reader connected via wire) occurs through a “Bluetooth Intercom” communication profile. This type of Bluetooth communication protocol is the “mono” type, with low quality. This means that the pillion passenger will hear music sources at a lower audio quality compared to the rider, in any event maintaining the balancing of voice communication at a higher level.
If you do not wish to share audio sources with the helmet connected via intercom, you can pair up the helmets according to the “Bike-to-Bike” mode (see controls diagram). By doing so, the audio of incoming sources will not be transmitted to the other helmet. The pillion passenger will be able to choose his/her favourite radio station, while keeping the Bluetooth intercom connection open with the rider.

Proceed as follows: pair up the mobile phone with the N-Com BX4. The “music via A2DP” connection is activated when you access the first menu of the N-Com system. The connection may require a few seconds (up to 10), and will be confirmed by an acoustic signal in the helmet. To start playing music, press “+” for 2 seconds. You will now be able to listen to music in the helmet (only when you are on the first menu of the N-Com device).

N.B.: With certain mobile phone models, in order to activate music via A2DP, you may have to start playing the music FIRST from the mobile phone and THEN from the N-Com device.

If you want to talk in intercom mode with your pillion passenger, however without sharing with him/her the audio coming from an external source or from the built-in FM radio, you can carry out the “Bike-to-Bike” pairing up between the two N-Com systems, following the procedure described in the User manual.
By doing so, rider and pillion passenger can talk to each other, yet each one can listen to their own favourite radio station or external multimedia source.
In the “Bike-to-Bike” mode, the Conference Call and GPS functions ARE NOT active.

The system has been tested with some satellite navigators. It is recommended to refer to the compatibility table on the Internet site. Nolan cannot guarantee proper operation with GPS systems that have yet to be tested.

The BX4 system can manage both connections (GPS system and passenger's). During communication between the GPS system and the helmet, the intercom connection is interrupted and only resumed at the end of the GPS communication.
If you wish, you can activate the “GPS Conference Function”.

Thanks to the GPS Conference Function, you can keep the "Rider-Passenger" intercom open even while the satellite navigator is giving instructions, thus preventing the intercom to be turned off every time a message comes in from the navigator.

Note: this function is available only if the Pillion Passenger helmet is also equipped with a N-Com system provided with the same function.

The BX4 system can only connect to one device at a time. Some GPS navigators allow Bluetooth connection to specific mobile phone models.
In these cases, the BX4 will allow connection to a navigator and, through the navigator, to your mobile phone. Check the compatibility of your mobile phone with the navigator.

You have to answer by pressing the answer button on the navigator. Once the call has been answered, it will be transferred to the helmet. You then have to hang up through the navigator as well. If the phone is connected to the navigator, and the latter is connected to the N-Com system, it will not be possible to answer the call from the helmet.

Every time you do an update of the Zumo 660, the GPS generate "false pairings" that fill all the available memory. In fact, after updating of the Zumo, in the List of paired devices, you can see "blank dots" with no paired devices. To solve the problem, you have to erase all the pairings and try again to pair the Bluetooth system to the Zumo.

X-lite N-Com helmets have received ECE 22-05 standard approval (currently in force in Europe) including when the N-Com system is activated. Consequently, Nolan helmets comply with legislative requirements, even when they are equipped with one of the N-Com communication systems.

The volume of the system not only depends on the X-Series system, but also on the devices it is connected to (Mp3 players, mobile phones, radios, etc...).

Important: Adjust the volume of the X-Series system (where possible) and of the audio sources connected to it before using the system on the road.

Important: Adjust the volume of the X-Series system (where possible) and of the audio sources connected to it before using the system on the road. Prolonged exposure to high volume sounds might result in hearing damage.

Important information to avoid hearing damage
Permanent hearing loss might result from using the X-Series system at a high volume. Set the volume at a safe level. With time, listening to high volume sounds might feel normal, however it does lead to hearing damage. If you hear buzzing or muffled sounds, stop the playback and have your hearing checked. If you keep the volume low, you can increase your listening time without damaging your hearing.

There are many factors that affect communication (aerodynamic exposure of the motorcycle, helmet used, environmental noise, etc…), so it is impossible to define a limit beyond which communication becomes unacceptable.

Bluetooth Kit X-Series was devised for easy installation inside the helmet by the user. No special equipment or modifications are required for the helmet, since the helmet itself is designed to house the X-Series communication system.

No. The Nolan Group devised the X-Series system specially for X-lite helmets with N-Com X-Series attachments. For a list of helmets with N-Com X-Series attachments, please visit the website.

After installing the Bluetooth Kit X-Series (see instruction leaflet), you only need to pair up the Bluetooth Kit X-Series system with your mobile phone. In case the passenger's helmet is also equipped with an N-Com, X-Series or MULTI Bluetooth Kit system, you will also need to pair up the two N-Com systems (see instruction leaflet).

No. All pair-ups are stored in the memory, even when the helmets are switched off, and are maintained when the helmets are switched on again.

This configuration is possible if the two helmets – equipped with a N-Com, X-Series, MULTI Bluetooth Kit system - are less than ten metres apart.

If the connection fails (a failed Bluetooth connection is signalled by a beep in the earphone), briefly press and hold the “on” button (acoustic signal). This activates the search for the other helmet.

Sound quality depends on the audio equipment used and on the volume level. The volume of the audio device or of the Bluetooth kit should be adjusted so that it is not too high, as this might distort the sound.

Warning: Listening to other equipment should not interfere with driving the vehicle, which is top priority. Carry out all operations on the electronic equipment and on the X-Series system with the vehicle stopped, in compliance with Traffic Regulations.

Warning: Listening to high volume levels can distract you from driving the vehicle and may result in dangerous situations or reduce the ability to hear external noise.

Warning: Listening to high volume levels may result in hearing damage.

The Bluetooth Kit X-Series system is certified by the Bluetooth SIG Association, and it is therefore compatible with mobile phones equipped with a certified Bluetooth system. However, not all the functions on mobile phones might be available. For further information, refer to the Internet site.

• Automatic answer: Set this function on your phone (if available) and the call goes straight through the helmet without you having to press any key.
• Manual answer: If the phone paired up with the helmet receives a call, a special tone is sounded instead of the ring tone (this tone depends on the phone). To answer the call, stop the vehicle in a suitable place (in compliance with the Highway Code), then briefly press one of the three buttons ("on", "+" and "-").

Press "on" for two seconds

Stop the vehicle in a suitable place, in compliance with the Highway Code.
Make the call according to your mobile phone instructions:

• By using the phone keypad;
• By pressing "on" for 2 seconds (if voice commands are available).

Only certain models of mobile phones let you reject an incoming call (Hands-Free profile) by pressing the "on" button for 2 seconds.

Yes. The Bluetooth Kit X-Series system allows each helmet, the rider’s or the passenger’s,  to maintain connection to the phone and to the other helmet.

The connection between the rider’s helmet and the passenger's is put on hold and the rider is able to take the call. The passenger will not hear the caller’s voice, and will not be heard by the caller.
Rider and passenger will be automatically reconnected at the end of the phone call.

Yes. Just press “+” and “-” at the same time.

Yes. The Bluetooth Kit X-Series system can be connected to or disconnected from the mobile phone directly from the helmet by using the following controls:

• "on", pressed for 2 seconds to start the connection;
• "+" and "-" pressed simultaneously for 2 seconds to disconnect.

You can listen to music via Bluetooth connection with a mobile phone in Stereo mode if the mobile phone is equipped with an A2DP profile. To check if this is the case, please refer to your mobile phone manufacturer’s webpage or go to www.a2dp.info
Some mobile phones send music to the helmet by means of the Hands-Free (HF) profile, which is normally used for phone calls. The resulting audio quality will be inferior and sound will be emitted in Mono mode.

Yes. Each time "+" or "-" are pressed (a confirmation beep is heard in the earphones), the volume goes up or down a level, until a maximum or minimum level is reached, corresponding to a high and a low-pitched beep respectively. There are 7 volume levels, from a minimum level to a maximum level.

The Bluetooth X-Series system can only connect to one device at a time. However, it can store more than one device previously paired up. When turned on, the system automatically searches for the last used device that can be found in its range. If more than three devices have been paired up, the connection can be activated directly from the device.

• Make sure that the Bluetooth Kit X-Series system is working by switching on and adjusting the volume.
• Switch off the e-box again and pair up the N-Com Bluetooth Kit X-Series with the mobile phone.
• Check that the pair-up is correct by making and receiving a phone call.

To answer the call, stop the vehicle in a suitable place (in compliance with the Highway Code), then briefly press one of the three buttons (“on”, “+” and “-”). “Briefly” means anything up to 1 second, depending on the phone used (not on the X-Series system).

This problem occurs ONLY for software versions 2.00 or older (check software version by pairing up the Bluetooth Kit X-Series to any mobile phone and then reading the name displayed on the device screen). The problem can be solved by using the control that deactivates A2DP connection on the passenger's helmet (press "-" for 2 sec.). This will eliminate any feedback.

Unfortunately, some phones perform badly due to their software. Although the phone does not allow voice calls, it stays connected to the X-Series system so you can still receive phone calls. Normally, receiving a phone call solves the problem. Should this fail to work, switch the phone off and switch it on again.

This anomaly, found in some software versions of the N70 model, is linked to improper management of voice calls. If the phone continues to cause problems, you will have to make calls directly from the phone. Do not make calls while you are riding.

No, you cannot listen to the radio directly from a Nokia N70 that does not broadcast radio sound via Bluetooth.

This anomaly is due to the software installed in the mobile phone.
Download the procedure to adjust the volume of the telephone conversation.

This function is only possible in case the paired-up devices (MP3 players, mobile phones) are equipped with A2DP profile.

A2DP (Advanced Audio Distribution Profile) is a Bluetooth profile for high sound quality playback from an audio source equipped with this profile. The N-Com Bluetooth Kit X-Series is equipped with A2DP and can therefore be connected to mobile phones or music players broadcasting audio by using this profile.

Please refer to your mobile phone manufacturer’s webpage or go to www.a2dp.info

AVRCP (Audio Video Remote Control Profile) is a specific Bluetooth profile designed to control, via Bluetooth, Mp3 players (or mobile phones) equipped with A2DP. With the N-Com Bluetooth Kit X-Series, you can use the Play, Pause, Forward (Next track) controls directly from the helmet, with no need for manual operations from the connected device.

Yes. Just pair up the N-Com Bluetooth Kit X-Series.

Check if the A2DP profile has been installed on your mobile phone, or if it transfers music via HFP (Hands-Free Profile). With HFP, the resulting audio quality will be inferior and sound will be emitted in Mono mode. To check if your mobile phone is equipped with A2DP, please refer to the documentation supplied with the phone or go to www.a2dp.info

Yes. However, one signal will overlap the other.

Press “+” for 2 seconds to activate the "Pause" control during Bluetooth audio playback. The audio via cable will still be transferred.

Make sure the Bluetooth music player with A2DP profile is disconnected by pressing “-” for 2 seconds. If the Bluetooth music player is connected, the intercom connection via Bluetooth cannot be activated.

Both rider and passenger will be able to hear the music. When the passenger is disconnected, he/she will be cut off and will not be able to listen to the music. While music is playing, the intercom is on and you can talk with music in the background. To mute the microphones, reducing the noise they pick up, you can activate the "mute" function (press the "-" button for 4 seconds - double sound signal). To deactivate the "mute" function, press the "-" key for 4 seconds.

No. Another helmet cannot be connected via Bluetooth if the A2DP profile is used.

No. It is not possible to connect a passenger and an Mp3 player via Bluetooth at the same time.

Yes. The passenger will listen to high quality sound music in mono mode.

If the two helmets are connected via Bluetooth, both can use the "IN" connector to connect to an audio device. The audio from the connected devices will be heard by both rider and passenger.

Yes. Once the X-Series system is paired up with and connected to the phone, the music is played directly through the X-Series system. If a phone call is received or made, the Mp3 player is stopped and playback has to be resumed manually.

Notes: The N70 phone is not equipped with A2DP. Mp3 tracks will be played in Mono mode and with low quality sound.

The system has been tested with some satellite navigators. Please refer to the compatibility table on the Internet page. Nolan cannot guarantee proper operation with GPS systems that have yet to be tested.

You will need a cable connection to listen to high quality sound music with Garmin ZUMO. With a Multimedia Wire2 cable connection, you will be able to listen to high quality sound music in Stereo mode, but not to use a phone connected via GPS system. If you use a Multimedia Wire cable, you will be able to listen to high quality sound music in Mono mode. Bluetooth connection to the Garmin ZUMO allows listening to low quality sound music (Hands-free Bluetooth profile).

The Bluetooth Kit X-Series system can manage both connections (GPS system and passenger's). During communication between the GPS system and the helmet, the intercom connection is interrupted and only resumed at the end of the GPS communication.

During connection with a satellite navigator, you will be able to talk with  the passenger in intercom mode via cable connection. When receiving directions from the satellite navigator, the intercom mode will be momentarily paused and then automatically resumed. If the satellite navigator is used as an Mp3 player, the intercom mode is interrupted and the passenger will need to be reconnected.

The Bluetooth Kit X-Series system can only connect to one device at a time. Some GPS navigators allow Bluetooth connection to specific mobile phone models.
In these cases, the Bluetooth Kit X-Series will allow connection to a navigator and, through the navigator, to your mobile phone. Check the compatibility of your mobile phone with the navigator.

You have to answer by pressing the answer button on the navigator. Once the call has been answered, it will be transferred to the helmet. You then have to hang up through the navigator as well. If the phone is connected to the navigator, and the latter is connected to the X-Series system, it will not be possible to answer the call from the helmet.

The problem presents itself when the Bluetooth Kit X-Series card used on the rider’s helmet is equipped with a firmware version prior to 2.02; in this case, after a few connection and disconnection cycles of the Bluetooth intercom, the passenger’s card may stop working; you will have to turn off the system and turn it on again.
Turn to your local dealer to have the software in the rider’s card updated.

The problem presents itself when the Bluetooth Kit X-Series card used on the rider's helmet is equipped with a firmware version prior to  2.1; in this case, upon receiving several messages from the navigator one right after the other, it may happen that the two cards cannot complete the disconnection and reconnection cycle, consequently the Bluetooth intercom is not automatically restored when the navigator is done giving directions.
In this case, you will have to turn the passenger’s card on and off to properly restore all connections.
Turn to your local dealer to have the software in the rider’s card updated.

If you paired N-Com BX4 with I-Phone and then erased the BX4 from the memory of the mobile phone, to do another pairing between I-Phone and BX4 it is necessary to:

◦ RESET the paired devices from the memory of BX4 (see Manual Instruction of BX4)

◦ Repeat the pairing between BX4 and I-Phone